Revmping interior doors

davsue23 · Post by **davsue23** » Sun Mar 25, 2007 12:29 pm

Hi
My interior doors have suffered some damage from a over irate teenager.

They are only the cheap hollow doors but I cannot afford to replace them all. SO I am looking for ways to repair either by filling or I thort maybe i could cover them with a new skin of very thin sheet plywood, (i think thats what I mean ). I realise that this could affect the opening of the door.
So advise please on the above or a recomended filler for the holes

Many thanks

dewaltdisney · Post by **dewaltdisney** » Sun Mar 25, 2007 12:45 pm

One way is to cut the damaged area back to solid area in the form of a rectangle. Cut a piece of thin MDF or hardboard big enough to allow you to pass it through the hole on the short edge. Drill a small hole and tie a bit of string through it and then carefully slide the and the repair patch through the hole and rotate it to cover the opening. Squirt a load of No More Nails or similar and pull the string to move the patch into position. Tie up the string in a sort of tourniquet to hold it firm whilst the glue sets.

When ready, fill the area between the patch and the door surface and skim it flush. This may take a couple of applications. Rub down and paint to suit.

If the doors are veneered it can be done but to be honest it would not be worth it.

If you would like I will come around and beat the sh*t out of the teenager to show him what his face will do to a door.

DWD

davsue23 · Post by **davsue23** » Sun Mar 25, 2007 12:58 pm

I thanks for that he's grown out of that phase now, back to the person he was before the hormones set in

Hinton Heating · Post by **Hinton Heating** » Sun Mar 25, 2007 3:32 pm

to do the job with a lot less work... you could cut a sheet of hardboard to the size of the door frame gap, rather than the size of the door...

so about 20mm less width than the door, and 10mm less height.

You can get the sheets cut to size at most suppliers.

then just stick onto the door using "no more nails" you will have to refix the handle through the new skin.

wood4fun · Post by **wood4fun** » Sun Mar 25, 2007 4:36 pm

remove the door from his bedroom and change it over let him live the broken door.

panlid · Post by **panlid** » Sun Mar 25, 2007 5:07 pm

grab his head and smash it through the door. tell him it now has an air vent and if he carries on the rest of the doors will have vents to. even the solid doors

Marc · Post by **Marc** » Mon Mar 26, 2007 10:04 am

I'm with panlid on this. Smash his head through every door in the house and then they will all match and look better. Afterwards don't buy him any food until either he leaves home or you have saved enough money to buy a new door.

davsue23 · Post by **davsue23** » Mon Mar 26, 2007 4:09 pm

Well thank you for all your helpful comments

If I go down the plywood/hardwood route what would be the thickness I would use

sparkydude · Post by **sparkydude** » Mon Mar 26, 2007 4:24 pm

You could just get some expanding foam filer and pump this into the door cavity. wait to dry then just cut back, skin of flexible car body filler over it , light sanding, paint and job done.

Nick

Marc · Post by **Marc** » Mon Mar 26, 2007 4:52 pm

DWD's method will give a better base to fill but foam would probably work. I wouldn't use car filler as it is harder than polyfiller and you might have a job sanding it down without removing too much of the surounding door.

dirtydeeds · Post by **dirtydeeds** » Tue Mar 27, 2007 8:03 pm

pu a steel plate to the door

that will sort the teanager out, he (or she

) will never smash the door with a fist again

dont do this in a wimpey house you might have to underpin it