sliding miter saw £80

big-all · Post by **big-all** » Mon Apr 22, 2013 4:47 pm

great price 3 year gtee

http://www.lidl.co.uk/cps/rde/www_lidl_ ... =1706&ar=1

if it breaks you get your money back

wine~o · Post by **wine~o** » Mon Apr 22, 2013 4:50 pm

Don't rush off down there tonight though...

Starts MONDAY....29th of April...

big-all · Post by **big-all** » Mon Apr 22, 2013 4:55 pm

yes all lidl offers are day specific
and if you want one go there as near to opening time as you can

valve90210 · Post by **valve90210** » Tue Apr 23, 2013 9:03 am

I'm wondereding about getting one of these, could do with a sliding mitre saw as my existing nonsliding one, whilst pretty good won't be any good when I come to do some decking in the coming months as it doesn't have a deep enough cut.

Anyone any experience with these Lidls tools?

Also looking at the SDS drill for £40...

big-all · Post by **big-all** » Tue Apr 23, 2013 9:51 am

you cant go wrong really if it packs up within 3 years you get your money back

i would recommend lidle stuff for diy you dont often get failures reported on here and theres plenty buying there stuff

the only thing i have had problems with is the screws are soft and chew easily but that was 10 years ago

valve90210 · Post by **valve90210** » Tue Apr 23, 2013 10:37 am

Hmm, might have to check it out on monday, would be very handy for cutting decking boards! Might invest in a set of the cutting blades too... sure they won't last forever but would be good to have backups!

Job and Knock · Post by **Job and Knock** » Tue Apr 23, 2013 1:24 pm

I've had LIDL 190mm saw blades in the past and TBH for general carpentry work I couldn't fault them, certainly not at the price

valve90210 · Post by **valve90210** » Tue Apr 30, 2013 9:53 am

Well, yesterday morning I went along at opening time and picked up the sliding mitre saw, 2 packs of spare blades (I have another non-sliding mitre saw that they will fit), a nice garden broom, a set of spirit levels and some velcro-backed sanding pads that will fit my Bosch multi-tool.

Had a bit of a tinker with the mitre saw last night and have to say it seems to be a decent bit of kit, nice and sturdy and should suit my needs perfectly as I'm just a diyer!!

big-all · Post by **big-all** » Tue Apr 30, 2013 10:24 am

check the the pads as the velcro can vary
i assumed velcro was velcro but the lidl pads i bought probably 10 years ago for the same delta sander in the advert stick to the sander but not bosch base

valve90210 · Post by **valve90210** » Tue Apr 30, 2013 11:33 am

big-all wrote:check the the pads as the velcro can vary
i assumed velcro was velcro but the lidl pads i bought probably 10 years ago for the same delta sander in the advert stick to the sander but not bosch base

That's a good point...mind you they were only £2.99 for 30 so no great loss if they don't stick to it. Also, somewhere I have another sander they might stick to..though god knows where!!! :)

valve90210 · Post by **valve90210** » Mon Jun 03, 2013 9:39 am

Just to say I finally got around to using the mitre saw yesterday and it did a grand job of cutting some board.

The board was too wide so I have to cut and flip and it seems that the blade was pretty straight and square and the cuts went nicely.

big-all · Post by **big-all** » Mon Jun 03, 2013 10:22 am

when you are flipping boards try and leave 50% for the second cut to leave the maximum strength
also if you are cutting faced boards rotate rather than flip so all the chipping is on one face

happy handyman · Post by **happy handyman** » Mon Jun 03, 2013 3:11 pm

Bought this saw the other week.....not used yet.....looks good

valve90210 · Post by **valve90210** » Tue Jun 04, 2013 9:34 am

big-all wrote:when you are flipping boards try and leave 50% for the second cut to leave the maximum strength
also if you are cutting faced boards rotate rather than flip so all the chipping is on one face

Thanks for the tip re leaving 50% I hadn't thought of that!

Thinking about it I did rotate the boards rather than flipping for that very reason as the blade in the saw is a fairly rough one so it did splinter the wood a little on the edges which I wanted to keep to one side.

sliding miter saw £80

sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80

Re: sliding miter saw £80