Mouse

All your computer hardware and software questions in here please.

Moderator: Moderators

Post Reply
User avatar
ayjay
Senior Member
Posts: 9891
Joined: Wed Nov 17, 2010 5:51 pm
Has thanked: 458 times
Been thanked: 1708 times

Mouse

Post by ayjay »

My mouse seems to be getting a bit long in the tooth.

The main problem being that the scroll wheel is not always responding fully to my efforts.

Ebay has new ones exactly the same (suits me) for £6.00.

Is there a simple fix for a dodgy scroll wheel or do I just buy a new mouse - I think I can run to £6 without starving myself. :mrgreen:

If it makes any difference, it's a Logitech M-SBF96.
mouse2.jpg
mouse2.jpg (87.44 KiB) Viewed 2952 times
One day it will all be firewood.
User avatar
kellys_eye
Senior Member
Posts: 12309
Joined: Mon Mar 15, 2010 11:49 pm
Location: Oban
Has thanked: 357 times
Been thanked: 1790 times

Re: Mouse

Post by kellys_eye »

Scroll wheels operate via a slotted disk arrangement and they quickly pick up hair, fibres etc that interfere with the light beam and interrupt operation. It's easy to take one apart and scrape/clean the mechanism and the difference it makes is often remarkable.
Don't take it personally......
Bob225
Senior Member
Posts: 4764
Joined: Sun Jan 31, 2010 9:21 pm
Location: Kent, Land of Apples and PYO
Has thanked: 100 times
Been thanked: 876 times

Re: Mouse

Post by Bob225 »

yep there optical, back in the day when mice had balls the rollers and optics always got fouled up, usual its 4 screws unless its cheap it clipped together job

a mouse is something you use all the time, so getting a decent mouse to suit your hand(s) is a big factor I tend to go for the Microsoft optical wheel mouse - not the basic one but the one that is weighted other alternatives are a Logitech tracker ball or a touchpad
User avatar
ayjay
Senior Member
Posts: 9891
Joined: Wed Nov 17, 2010 5:51 pm
Has thanked: 458 times
Been thanked: 1708 times

Re: Mouse

Post by ayjay »

kellys_eye wrote:Scroll wheels operate via a slotted disk arrangement and they quickly pick up hair, fibres etc that interfere with the light beam and interrupt operation. It's easy to take one apart and scrape/clean the mechanism and the difference it makes is often remarkable.
Does that apply to an optical mouse, or are you thinking of an older type?

I can remember cleaning little rubber balls on daily basis, but this mouse is well over 5 years old and apart from blowing the odd hair of the bottom of it it's not been a problem so far.

Would cleaning it require the PC to be off and mouse unplugged?
One day it will all be firewood.
User avatar
BillyGoat
Troll Headbutter
Posts: 8071
Joined: Sat Jan 01, 2011 8:20 pm
Location: On top of a mountain, in the long grass.
Has thanked: 386 times
Been thanked: 796 times

Re: Mouse

Post by BillyGoat »

I just buy new ones :lol:

WEll, when I say buy........ :lol:

On my desktop, I've got a Logitech MX510 - best mouse I've EVER owned. I think the MX518 replaced it......ignore the gamer part, it's just SO comfey to use all day. Love it and I'll be sad when it dies.

BG
Arguing with a woman is like reading a Software Licence Agreement.
In the end, you ignore everything and click "I agree".
Bob225
Senior Member
Posts: 4764
Joined: Sun Jan 31, 2010 9:21 pm
Location: Kent, Land of Apples and PYO
Has thanked: 100 times
Been thanked: 876 times

Re: Mouse

Post by Bob225 »

The early mice used rollers for direction this was on a shaft, the other end had a slotted disc with a ir sender and a receiver the other side of this disc as you rolled the mouse the light pulses where translated electrical pulses, technically they where "optical"
User avatar
kellys_eye
Senior Member
Posts: 12309
Joined: Mon Mar 15, 2010 11:49 pm
Location: Oban
Has thanked: 357 times
Been thanked: 1790 times

Re: Mouse

Post by kellys_eye »

The sh1t still gets in through the wheel slot even if yours is an optical mouse. I get 'fond' of the mouse (and keyboard for that matter) and would rather clean/repair a dodgy one than have to get used to the peculiarities of a new one (even if they only take a few minutes to adapt to :roll: ).

Plus I'm a cheapskate....... :lol:
Don't take it personally......
User avatar
ayjay
Senior Member
Posts: 9891
Joined: Wed Nov 17, 2010 5:51 pm
Has thanked: 458 times
Been thanked: 1708 times

Re: Mouse

Post by ayjay »

kellys_eye wrote:The sh1t still gets in through the wheel slot even if yours is an optical mouse. I get 'fond' of the mouse (and keyboard for that matter) and would rather clean/repair a dodgy one than have to get used to the peculiarities of a new one (even if they only take a few minutes to adapt to :roll: ).

Plus I'm a cheapskate....... :lol:
I'll take a screwdriver to it before I lash out the £6.00 then.

Is it safe to do it "live", or should I disconnect everything?
One day it will all be firewood.
User avatar
kellys_eye
Senior Member
Posts: 12309
Joined: Mon Mar 15, 2010 11:49 pm
Location: Oban
Has thanked: 357 times
Been thanked: 1790 times

Re: Mouse

Post by kellys_eye »

Disconnect - unless you want to be fixing your PC as well :lol:
Don't take it personally......
User avatar
ayjay
Senior Member
Posts: 9891
Joined: Wed Nov 17, 2010 5:51 pm
Has thanked: 458 times
Been thanked: 1708 times

Re: Mouse

Post by ayjay »

I spoke to my nipper who said I might struggle to get it all back together again so I splashed out the £6.00 for a new one: it's plugged in now and the dory is completely hunky again. :-)

Now I can take the old one apart and play. :mrgreen:
One day it will all be firewood.
User avatar
BillyGoat
Troll Headbutter
Posts: 8071
Joined: Sat Jan 01, 2011 8:20 pm
Location: On top of a mountain, in the long grass.
Has thanked: 386 times
Been thanked: 796 times

Re: Mouse

Post by BillyGoat »

Speaking of mice....saw this on HotUKDeals: http://www.ebay.co.uk/itm/310792260381? ... 6448297101

3 quid for a wired mouse....not too shabby
Arguing with a woman is like reading a Software Licence Agreement.
In the end, you ignore everything and click "I agree".
DIY_Johnny
Mr. Grumpy
Posts: 3193
Joined: Tue Nov 18, 2008 3:41 pm
Has thanked: 25 times
Been thanked: 109 times

Re: Mouse

Post by DIY_Johnny »

I bought the Logitech M525 and K750 keyboards. Fantastic. Battery on mouse lasts for long long time, very responsive. Keyboard is wireless solar powered, requires hardly any light, sturdy but exceptionally thin. Both can use the one nano receiver, has a long range which is great when watching a movie so can put keyboard beside you for stop/start etc

Only downside is price, dear me not cheap :sad:
User avatar
ayjay
Senior Member
Posts: 9891
Joined: Wed Nov 17, 2010 5:51 pm
Has thanked: 458 times
Been thanked: 1708 times

Re: Mouse

Post by ayjay »

ayjay wrote:I spoke to my nipper who said I might struggle to get it all back together again
He knows nothing that boy!!

I could make a fur coat for a mouse from the fluff inside it though. :lol:

DIY_Johnny wrote:I bought the Logitech M525 and K750 keyboards. Fantastic. Battery on mouse lasts for long long time, very responsive. Keyboard is wireless solar powered, requires hardly any light, sturdy but exceptionally thin. Both can use the one nano receiver, has a long range which is great when watching a movie so can put keyboard beside you for stop/start etc

Only downside is price, dear me not cheap :sad:
I just wanted a like for like replacement, I'm not into change, that mouse does all I want, comfortably, and only £6.00. That's easily less than £1 per year. What's not to like? :mrgreen:
One day it will all be firewood.
Post Reply

Return to “Computers”